TFT彩屏
TFT触摸屏
HDMI TFT显示器
工业级TFT屏
条型TFT屏
圆形TFT屏
方形TFT屏
全视角TFT屏
电阻触摸TFT屏
电子墨水屏
高亮液晶屏
树莓派触摸屏
OLED模块
| Product: | 0.96 Inch OLED Display | Number Of Pixels: | 128x64 Pixels |
| Driver IC: | SSD1315 Or Equivalent | Display Mode: | Passive Matrix |
| Display Color: | Monochrome (white) | Drive Duty: | 1/64 Duty |
| Panel Size: | 24.7 X 16.6 X 1.3 (mm) | Active Area: | 21.74 X 11.175 (mm) |
| Pixel Pitch: | 0.17 X 0.175 (mm) | Pixel Size: | 0.15 X 0.15 (mm) |
| Viewing Direction: | All Viewing Angles | Interface: | I2C, SPI Optional |
| Connection: | Plug-in | Pin Number: | 30 Pins (Can Be Customized） |
| Operating Temp.: | -40C - +70C | Storage Temp.: | -40C - +85C |
| Life Time: | 50,000 Hours @60cd/m2 | Compliance: | REACH & RoHS Compliant |
| Highlight: | 0.96 Inch OLED Display Module, OLED Display Module 128x64 | ||
0.96 英寸 OLED 显示屏 128x64 白色/蓝色/黄色/黄蓝色产品介绍
单色 OLED 显示屏是指只能显示一种颜色的 OLED 显示屏，例如白色、蓝色和黄色。这三种颜色在大多数用户中相当常见和流行。此外，在此显示屏上，我们还可以提供黄色和蓝色的双色显示，这也为用户提供了良好的视觉体验。
SFOS096XZ-7127AP OLED 显示模块是一款 128x64 分辨率 COG 图形显示屏，对角线尺寸为 0.96 英寸。OLED 型号设计为工业级，具有价格竞争优势。该模块内置 SSD1315 IC；支持 I2C 和 SPI 接口。逻辑电源电压为2.8V，显示电源电压为9V，VDD工作电流为160μA，驱动占空比为1/64。
SFOS096XZ-7127AP OEL显示模块适用于可穿戴设备、智能家居应用等。该模块可在-40℃至+70℃的温度范围内工作；其存储温度范围为-40℃至+85℃。
特性
| Product: | 0.96 inch plugging connection OLED Display |
| Number Of Pixels: | 128x64 Pixels |
| Driver IC: | SSD1315 Or Equivalent |
| Display Mode: | Passive Matrix |
| Display Color: | white, blue, yellow and dual color(yellow/blue) |
| Drive Duty: | 1/64 Duty |
| Active Area: | 21.74 X 11.175 (mm) |
| Panel Size: | 24.7 X 16.6 X 1.3 (mm) |
| Pixel Pitch: | 0.17 X 0.175 (mm) |
| Pixel Size: | 0.15 X 0.15 (mm) |
| Interface: | I2C, SPI Optional |
| Viewing Direction: | All Viewing Angles |
| Connection: | Plug-in |
| Pin Number: | 30 Pins (Can Be Customized) |
| Operating Temp.: | -40C - +70C |
| Storage Temp.: | -40C - +85C |
| Life Time: | 50,000 Hours @60cd/m2 |
| Compliance: | REACH & RoHS Compliant |
0.96 英寸 OLED 显示屏 128x64 Ｗ白色/蓝色/黄色/黄蓝色产品图
接口引脚定义
| No | Symbol | Description |
| 1 | NC | No connection. |
| 2 | C1N | CXP/CXN-Pin for charge pump capacitor;Connect to each other with a capacitor |
| 3 | C1P | |
| 4 | C2P | |
| 5 | C2N | |
| 6 | VBAT | Power supply for charge pump regulator circuit. |
| 7,10 | NC | No connection |
| 8 | VSS | This is a ground pin |
| 9 | VDD | Power supply pin for core logic operation. |
| 11 | BS1 | |
| 12 | BS2 | MCU bus interface selection pins. |
| 13 | CS | This is the chip select input.(active LOW) |
| 14 | RES | Reset signal input.when the pin is pulled LOW,initialization of the chip is excute. Keep this pin HIGH(i.e connect to VDD)during normal operation |
| 15 | A0 | This is Data/Command control pin. When it is pulled HIGH (i.e. connect to VDD), the data at D[7:0] is treated as data. When it is pulled LOW, the data at D[7:0] will be transferred to the command register. In I2C mode, this pin acts as SA0 for slave address selection. When 3-wire serial interface is selected, this pin must be connected to VSS. |
| 16 | WR | This is read / write control input pin connecting to the MCU interface. When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected. |
| 17 | RD | When connecting to an 8080-series microprocessor, this pin receives the Read (RD#) signal. Readoperation is initiated when this pin is pulled LOW and the chip is selected. When serial or I2C interface is selected, this pin must be connected to VSS. |
| 18 ~25 | D0 ~D7 | These are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus. When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serialdata input: SDIN and D2 should be kept NC. When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL. |
| 26 | IREF | This is segment output current reference pin. When external IREF is used, a resistor should be connected between this pin and VSS to maintain the IREF current at 30uA. When internal IREF is used, this pin should be kept NC. |
| 27 | VCOMH | The pin for COM signal deselected voltage level. A capacitor should be connected between this pin and VSS.Com |
| 28 | VCC | Power supply for panel driving voltage. This is also the most positive power voltage supply pin.When charge pump is enabled, a capacitor should be connected between this pin and VSS. |
| 29,30 | NC | No connection |
DC 特性
| Items | Symbol | Min. | Typ. | Max. | Unit | |
| Supply Voltage | Logic Supply Voltage IC | VDD | 1.65 | 3.0 | 3.5 | V |
| Charge Pump Regulator Supply Voltage IC | VBAT | 3.0 | 3.3 | 4.5 | V | |
| Operating(for OLED panel) | VCC | 7.0 | 7.5 | 8.0 | V | |
| Input Voltage | High Voltage | VIH | 0.8 x VDD | - | VDD | V |
| Low Voltage | VIL | 0 | - | 0.2 x VDD | V | |
| Output Voltage | High Voltage | VOH | 0.9 x VDD | - | VDD | V |
| Low Voltage | VOL | VSS | - | 0.1 x VDD | V | |
电光特性
| Items | Symbol | Min. | Typ. | Max. | Unit | Remark | |
| Operating Luminance | L | 50 | 65 | - | cd /m2 | All pixels ON | |
| Power Consumption | P | - | 50 | 60 | mW | 30% pixels ON | |
| Frame Frequency | Fr | - | 105 | - | Hz | - | |
| Color Coordinate | Blue | CIE x | 0.11 | 0.15 | 0.19 | CIE1931 | Darkroom |
| CIE y | 0.21 | 0.25 | 0.29 | ||||
| Response Time | Rise | Tr | - | 10 | - | us | - |
| Decay | Td | - | 10 | - | us | - | |
| Contrast Ratio | Cr | 10000:1 | - | - | - | Darkroom | |
| Viewing Angle | θ | 160 | - | - | Degree | - | |
| Operating Life Time | Top | 22000 | - | - | Hours | L= 65 cd/m2 | |
0.96 英寸 OLED 显示屏 128x64 Ｗ白色/蓝色/黄色/黄蓝色产品图
工厂设施和证书
手机/微信：135 0298 3321 柯先生
手机/微信：138 2960 7086 郑小姐
手机/微信：136 8686 7235 陈小姐
地址： 深圳市宝安区洲石路阳光工业区D栋
在线留言
135 0298 3321
首页 》 
